Chip Processing

• Approx 120 ft³/hour
• 36" diameter
• Material in-feed hopper with screw feed conveyor part
• Separator for bar ends/parts prior to wringer inlet
• 30 HP drive
• Pneumatic discharge transition pipe for processed dry chips
• Drag conveyor with discharge chute for collected coolant
• Return auger for recycling metal chips
• CSI “Wadbuster” for assisting material feed
• PLC Controls

30" Titan Automatic Vertical Bowl Continuous Chip Wringer System

• Rated for 2,000-3,000 lbs/hour (approx.)
• Pneumatic dry chip discharge transition pipe for processed dry chips
• Includes cart/hopper lift and dump station
• Material infeed hopper with screw conveyor
• Twin shaft inline shredder
• Parts separator for bar ends/parts prior to wringer inlet
• Collected coolant dragout tank with return auger for recycling swarf/chips
• Magnetic coolant/chip separator

• Continuous 30” wringer pneumatic discharge
• Transition pipe for processed dry chips
• Drip pan around perimeter for containment
• 3/4 HP pump for recycled coolant
• 20 HP Motor

Oberlin HB-8 fully automatic pressure filter system

• Rate for up to: 280 gallons per minute
• Media area: 7 sq. ft.
• Equally effective on oil, water, and synthetic coolants
• Extends coolant life 5 to 10 times by removing 90% solids by weight
• Accepts standard roll media
• Automatic media advance system with low media warning
• GE Electric PLC controls with machine-mounted operator control station

Oberlin OPF-7 fully automatic pressure filter chip processing system

• Capacity: up to 280 gallons per minute
• Media area: 7 sq. ft.
• Equally effective on oil, water, and synthetic coolants
• Extends coolant life 5 to 10 times by removing 90% solids by weight
• Accepts standard roll media
• Automatic media advance system with low media warning
• Machine-mounted operator control station

Oberlin OPF-7 fully automatic pressure filter chip processing system

• Rate for up to: 280 gallons per minute
• Media area: 7 sq. ft.
• Extends coolant life 5 to 10 times by removing 90% solids by weight
• Equally effective on oil, water, and synthetic coolants
• Accepts standard roll media
• Automatic media advance system with low media warning
• Allen Bradley PLC controls with machine-mounted operator control station

Applied Recovery Systems (ARS) RST-1000 foundry series hydraulic briquetter system, automatic cycle for continuous operation, large infeed hopper for wet chips, feed ram assist, material capacity - aluminum: 1,000 lbs/hr, steel or cast iron: 2,000 lbs/hr, copper or brass: 3,200 lbs/hr, briquette size: 3-1/2" x 3-1/2", total force available: 196 tons, MetalPress 600 PLC control system with control cabinet mounted on machine.

Mayfran/Reclamat Chip Wringer System, Wringer Cart Dump Infeed Auger Shredder Barret Fines Centrifuge 230/460 Volt, 60 Hz, 3 Phase Electrics

• Model #CA-6200 chip wringer with drip pan
• Containment tank in-feed dumper [carts not included]
• In-feed hopper with screen separator
• In-feed conveyor
• Bar end separator
• Transition chute for processed dry chips discharge
• Pressure pipe swivel fallout chute
• Operator control panel

U.S Centrifuge A120 Simplamatic Series automatic centrifuge, maximum flow rate: 15 gpm., bowl diameter: 12" , maximum bowl speed: 2,500 rpm., pneumatically operated solids plow for automatic sludge removal, factory equipped machine base with recirculating tank, Allen Bradley PLC and related control system.

• Includes CA-6200-E wringer with drip pan around perimeter for containment (project number: 51163)

30” Inter-Source continuous chip processing system

• CA-6200-E wringer with drip pan around perimeter for containment - project number: 5105908
• Titan Industries in-floor conveyor - serial number: 2007532
• 3600 series shredder with stand - project number: 5105903, serial number: M2-3624
• Operator control station with Allen Bradley PLC - project number: 5105912, serial number: 35131D
• Dump station
• Hopper in-feed with U-Trough screw conveyor feed
• Containment tank with pump
• Return chute and transition chute
• Fines drag conveyor with pump and discharge chute for collected coolant
• Swivel chute with photo-level sensor
• 25" cyclone
• Parts separator prior to wringer inlet

Oberlin fully automatic pressure filter chip processing system

• Rate for up to: 280 gallons per minute
• Media area: 7 sq. ft.
• Mueller Plate type heat exchanger unit
• Equally effective on oil, water, and synthetic coolants
• Extends coolant life 5 to 10 times by removing 90% solids by weight
• Accepts standard roll media
• Automatic media advance system with low media warning
• GE Electric PLC controls with machine-mounted operator control station
• INDEPENDENT TANK SOLD WITH AM11622

Oberlin #HA fully automatic pressure filter chip processing system

• Rated for up to: 96 gallons per minute
• Media Area: 2.4 sq. ft.
• 1/2” air line supply
• Accepts standard roll media
• Filters oil, water, and synthetic coolants
• AMT/Gushers Pump
• Machine-mounted push button controls

Oberlin #OPF-4 fully automatic coolant pressure filtration system for chip processing

• Capacity: 160 Gallon (water base)
• Media area: 4 sq. ft.
• Max filter pressure: 45 PSI
• Accepts standard roll media
• Extends coolant life 5 to 10 times by removing 90% solids by weight
• Machine-mounted push button type controls
• Automatic media advance system with low media warning

Oberlin #OPF-4 fully automatic coolant pressure filtration system for chip processing

• Capacity: 160 Gallon (water base)
• Media area: 4 sq. ft.
• Max filter pressure: 45 PSI
• Accepts standard roll media
• Extends coolant life 5 to 10 times by removing 90% solids by weight
• Machine-mounted push button type controls
• Automatic media advance system with low media warning

Oberlin #OPF-4 fully automatic coolant pressure filter system for chip processing

• Capacity: 160 gallons per minute (water based)
• Media area: 4 sq. ft.
• Max filter pressure: 45 PSI
• Fully automatic pressure filter system
• Accepts standard roll media
• Extends coolant life 5-10 times by removing 90% solids by weight